Mastercraft
Scie d'établi portatif Mastercraft de 13 A
#055-6739-8
349,99 $
Malheureusement, cet article ne fait plus partie de l’assortiment du magasin que vous avez sélectionné et les magasins de la région.
Ces produits similaires présentés ci-dessous pourraient vous intéresser.Objets similaires
À l'attention des personnes résidant au Québec: pour obtenir des renseignements sur l'entretien et la réparation, cliquez ici.
Objets similaires
Produit Détails
La robustesse d’une scie d’établi. La facilité de transport d’une scie circulaire. Cette scie d’établi vous accompagnera partout, et sa taille compacte assure un rangement facile. Les coupes longitudinales et les coupes d’onglet deviennent un jeu d’enfant. Elle peut également accueillir des lames à rainurer de 6 po grâce aux encarts de plaque à gorge fournis. Des années de découpage dans la joie.
Scie d'établi portatif de 10 po convient parfaitement aux travaux exigeant une scie sur place
120 V, 13 A, 5000 tr/min, 60 Hz
Lame de 10 po à 36 dents à pointes au carbure
Couteau séparateur à dispositif de protection
Profondeur de coupe à 90° : 3 po; profondeur de coupe à 45° : 2 1/2 po
Capacité de refente : 9 po à gauche et 16 po à droite
Rallonge télescopique et guide de refente à dégagement rapide
Warranty
- Limitée de 3 ans, réparation. Pour service clientèle, téléphoner à Mastercraft au 1 800 689-9928
Commande en ligne
- Le ramassage est gratuit dans la plupart des magasins (certains magasins exigent un montant minimum de commande avant taxes).
- Les tarifs d’expédition dépendent de la taille et du poids des articles, ainsi que de la distance entre l’adresse de livraison et le magasin.
- La livraison le jour même coûte 9,99 $ par commande.
- Informations sur une commande en ligne
Retours
- La plupart des articles peuvent être retournés ou échangés dans tous les magasins Canadian Tire dans les 90 jours suivant l’achat.
- Certains articles ne sont pas remboursables ni échangeables.
- La politique de retour décrite ci-dessus peut ne pas s’appliquer à l’article que vous consultez présentement. Pour obtenir tous les détails et connaître les critères d’admissibilité, veuillez consulter notre Politique de retour pour connaître les exceptions.
Comparer des articles semblables
Only Show Differences | Consultation en cours | |||||
| Ratings | ||||||
| Calibre du cordon (cal.) | 14ga | 14ga | 16ga | 14ga | ||
| Capacité de coupe en biseau | Unique | Unique | Unique | Unique | ||
| Coupe en biseau maximale (degrés) | 45 ° | 45 ° | 45 ° | 45 ° |
Acheter des produits connexes
- Offres hebdomadaires
- Les clients ont aussi consulté
- Vers les produits tendances
- Plus de cette marque
Offres hebdo
Points saillants de l'evaluation
Évaluations
Filtrer les avis
- achat
- prix
- installation
- en magasin
- résultats
- la satisfaction
- ajustabilité
- taille
Cote
Paramètre régional
1 to 4 sur 4 commentaire
1 – 4 sur 4 commentaire
Les plus récents
1 étoile(s) sur 5.
Do not purchase
il y a 11 ans
Just returned this product and I do appreciate the CTC satisfaction guarantee.
The fence was not straight nor was it square to the table and it had no adjustment capability.
The throat plate was not flush with the table and it snapped in place with a little spring clip to keep it in place.
There were no anti-kickback pawls nor allen keys included with my saw so do not throw away the packaging until you go over the complete parts list.
Traduire avec GoogleNon, Je ne recommande pas ce produit.
Utile?
Réponse de Mastercraft :
il y a 2 ans
Mastercraft
Hello, thank you for your attention. if you need any help, please call the toll-free helpline at 1-800-689-9928 for processional after-sales service. You can also log in to the CTR official website https://www.canadiantire.ca/en.html, to know more about product details.
2 étoile(s) sur 5.
fence, rail, and angle cuts are never true
il y a 13 ans
the fence mechanism is cheap and shifts on slight angles constantly, so a truly straight cut is almost impossible.
Also cutting anything at a 45 degree angle (either with the blade or the cheap rail attachment) will never actually be 45 degrees.
It's a bit of a nuisance.
Traduire avec GoogleNon, Je ne recommande pas ce produit.
Utile?
3 étoile(s) sur 5.
Montage
il y a 13 ans
Je viens de l'acheter ce matin en solde pour la fête des pères, pas vraiment d’explication pour le montage des pièces importante pour la sécurité, on doit deviner et regarder les images sur le net pour savoir ou ça va.
Oui, Je recommande ce produit.
Utile?
Réponse de Mastercraft :
il y a 2 ans
Mastercraft
Hello, thank you for your attention. if you need any help, please call the toll-free helpline at 1-800-689-9928 for processional after-sales service. You can also log in to the CTR official website https://www.canadiantire.ca/en.html, to know more about product details.
4 étoile(s) sur 5.
Great for home use A few initial problems
il y a 14 ans
I just bought this saw for light home use. I am impressed with the sturdy construction, portability, and it is easy to store.
I got it on sale for half the price of the DeWalt DW745 that I was also looking at. The DW745 has an impressive rack and pinion fence system, but I judged that the fence on the mastercraft with 5 inches of contact to square the fence against the table will be good for my requirements. Also the DW745 does not take dado blades, and the mastercraft will take 6 inch dado blades with the supplied dado throat insert.
I had 2 problems out of the box. The rear mount that attaches the saw and motor assembly to the bottom of the table was so out of alignment that the blade interfered with the throat plate. I corrected this by putting the table on its back, locating the 2 hex screws at this mount, loosen them, adjust the blade to the proper position then tighten. The other problem I had was the fence broke during one of my first cuts. I made the mistake of going to the store to get this corrected when all I had to do was call the 800 number on the owner’s manual and they sent another rip fence.
Once the blade was in place, the instruction book was good to follow for alignment. The offset cam adjustment to square the blade with the table was a bit confusing until I took this mechanism apart to see how it works. I have waxed the table.
I have tested this saw on 2x4’s 1x6 and composite flooring with both rip cuts and mitre cuts, and am pleased with the results. I can see if I want a very fine cut I will have to change the blade.
Hopefully this saw provides just as good service as the bottom of the line Canadian Tire 19 inch gas lawn mower I bought in 1983 and has been cutting my medium sized lawns for 28 years. It was bought in the days of leaded gas and I now use a lead substitute in the gas.
Traduire avec GoogleOui, Je recommande ce produit.
Utile?
Questions
Commencez à taper votre question et nous vérifierons si elle a déjà été posée et répondue.
1 - 10 sur 17 questions
Réponses les plus utiles
Q : Does it come with a Dado insert plate? If not can It be bought seperatly?
il y a 15 ans3 Réponses
- Traduire avec Google
R : If you are like me and enjoy getting the most from your purchases for the least money, I have the following suggestions. In addition to buying this saw for $170, I have made the following purchases: 6 Inch Dado Saw Blades p/n 55-1014-2 – For $70 I hesitated to buy this set with no immediate use, but on sale for $28 it was a no brainer. They should greatly increase the type of tasks I can do with this saw. The instruction book recommends 6 in blades rather than the more common 8 in, and a cut no wider than ½ inch. The saw designer has probably calculated that the inertia of this stack is about the same as a 10 inch blade. Any more would lead to an early failure of the saw. I tested this and got a maximum cut depth of 0.845 inches. If you want a wider cut than ½ inch, you can just move the wood sideways and make a second or multiple adjacent cuts. You may lose precision. Digital Caliper p/n 58-6800-4 – At $20 on sale this item provides much greater precision in laying out cuts and measuring them than a tape measure. It measures outside, inside, depth, and step to 2/1000 of an inch. Precision is the whole reason I bought the saw in the first place. Expandable C-clamp p/n 57-2662-8 – If you have acceptable c-clamps read no further, but if you need some to fasten auxiliary fence, or feather board you can get these for $4.43 each. They have a slip-lock mechanism on the spine. It may seem trivial but it allows you to position the clamp so you only have to make one or 2 turns of the screw. This is important when the turn handle is very close to the saw body. I found these in my store but not on the internet.
Anonymeil y a 14 ansUtile?
Q : Where can I find the manual? I bought this tool and it was missing the english manual. The blade is out of alignment and I need to adjust it but can't figure out where the adjustment bolts are. Where can I find the manual?
il y a 14 ans2 Réponses
- Traduire avec Google
R : The french manual and english manual are the same book and mine was included in the box. The alignment problem you might be having is not described in the manual. You may have to look under the table beside the throat near the rear for the appropriate screws.
il y a 14 ansUtile?
Q : Where can I buy part #556739239 for item 055-6739-8 by ordering it?
il y a 3 ans1 Réponse
- Traduire avec Google
R : Unfortunately , we no longer sell this part on the website
il y a 3 ansUtile?
Q : My motor just burnt out - Where can I buy a replacement? The product is 4 years old, and barely used.
il y a 8 ans1 Réponse
- Traduire avec Google
R : Please contact our toll-free helpline 1-800-689-9928. Thank you.
il y a 8 ansUtile?
Q : Bonjour,j'ai acheté cet item;il n'est plus garantie et je voudrais commander des pièces Ou dois-je m'adresser item: 055-6739-8
il y a 9 ans1 Réponse
R : Pour la disponibilité de pièces de remplacements, nous vous encourageons à contacter Mastercraft au 1-800-689-9928
il y a 9 ansUtile?
Q : motor has a slight grinding noise as it is winding down.....bearings???? or possibly brushes? can a new motor be bought? it is only 5 months old, I was pleased with the saw overall until it stalled out on a 2X4 today, and that is when I noticed the change in the wind-down noise....any suggestions?
il y a 11 ans1 Réponse
- Traduire avec Google
R : Please call customer service for replacement brushes and bushings.
il y a 11 ansUtile?
Q : Quel est le poids de ce banc de scie portable?
il y a 12 ans1 Réponse
R : Il pèse 54lbs
il y a 12 ansUtile?
Q : Does the blade guard lock in the up position to measure between blade and fence?
il y a 12 ans1 Réponse
- Traduire avec Google
R : Yes, the blade guard will lock in the up position.
il y a 12 ansUtile?
Q : Where can I purchase a replacement switch?
il y a 12 ans1 Réponse
- Traduire avec Google
R : Please call customer support. The parts list and phone number are located in your product manual.
il y a 12 ansUtile?
Q : what is the net weight of the saw without stand?
il y a 12 ans1 Réponse
- Traduire avec Google
R : 45lb 2oz (20.5kg)
il y a 12 ansUtile?
1 - 10 sur 17 questions
