NOTRE MAGASIN

Crédit Offert* EN SAVOIR PLUS

Soutien État de commande
EN
BernzOmatic

Baguettes de soudure et brasage en aluminium Bernzomatic, paq. 2

#058-0046-6
Baguettes de soudure et brasage en aluminium Bernzomatic, paq. 2
12,99 $
Achetez-le en ligne :
Ramassage à Leduc, AB
13 En stock
Obtenez-le dès aujourd’hui!

Ramassage disponible à 11 h 00, 02 janv.

Quantité mise à jour à 1
Nouveaux paiements numériques disponibles à la page de paiement
Trouvez-le également en magasin:
13 en stock au Leduc, AB
Allée 22
Ajouter au registre

À l'attention des personnes résidant au Québec: pour obtenir des renseignements sur l'entretien et la réparation, cliquez ici.

BernzOmatic
BernzOmatic

Baguettes de soudure et brasage en aluminium Bernzomatic, paq. 2

12,99 $

Produit Détails

Les baguettes de brasage et de soudage en aluminium Bernzomatic MD sont des outils parfaits pour une variété de tâches, y compris le brasage ou la réparation de fenêtres, de portes, de gouttières et de bardages en aluminium. Elles sont faciles à utiliser, que ce soit sur un chantier ou à la maison. Avec une température de travail basse de 720 à 750 degrés Fahrenheit, ces baguettes peuvent également être utilisées pour construire des joints en aluminium sans distorsion, décoloration ou perte de résistance. Elles ont une résistance à la traction de 33 000 lb/po 2 . Le paquet comprend deux baguettes.

  • Baguettes de soudure en aluminium à haute résistance pour des joints robustes en métal

  • Minimise la fissuration et la déformation du métal joint

  • Manche souple qui facilite la manipulation

  • Abaisse la température d'assemblage du métal

  • Résistance à la rupture : 25 000 lb/po2

  • Température de fusion : 700 à 750°F (371 à 399°C)

  • Comprend 2 baguettes

Numéro de modèle de l’article 328636
Classification des électrodes S. O.
Fonctionnalités avancées Sans fonctionnalités avancées
Hauteur une fois assemblé (cm) 36,83 cm
Hauteur une fois assemblé (pi) 1,21 pi
Hauteur une fois assemblé (po) 14,50 po
Largeur une fois assemblé (cm) 5,08 cm
Largeur une fois assemblé (mm) 50,80 mm
Largeur une fois assemblé (po) 2,00 po
Longueur une fois assemblé (cm) 0,51 cm
Longueur une fois assemblé (pi) 0,02 pi
Longueur une fois assemblé (po) 0,20 po
Matériau principal Aluminium
Nombre de pièces 2
Poids une fois assemblé (kg) 0,09 kg
Poids une fois assemblé (po) 0,20 lb
Position de soudage Toutes les positions
Type de fixations pneumatiques Baguette pour brasage
Utilisations du produit Tout usage, Plomberie, Tôle
Garantie
  • Cat article est couvert par une garantie spéciale. Pour de plus amples renseignements sur la garantie, rendez-vous à votre magasin Canadian Tire.
Commande en ligne
  • Le ramassage est gratuit dans la plupart des magasins (certains magasins exigent un montant minimum de commande avant taxes).
  • Les tarifs d’expédition dépendent de la taille et du poids des articles, ainsi que de la distance entre l’adresse de livraison et le magasin.
  • La livraison le jour même coûte 9,99 $ par commande.
  • Informations sur une commande en ligne
Retours
  • La plupart des articles peuvent être retournés ou échangés dans tous les magasins Canadian Tire dans les 90 jours suivant l’achat.
  • Certains articles ne sont pas remboursables ni échangeables.
  • La politique de retour décrite ci-dessus peut ne pas s’appliquer à l’article que vous consultez présentement. Pour obtenir tous les détails et connaître les critères d’admissibilité, veuillez consulter notre Politique de retour pour connaître les exceptions.

Comparer des articles semblables

Only Show Differences
Ratings
Classification des électrodesS. O.
Fonctionnalités avancéesSans fonctionnalités avancéesSans fonctionnalités avancéesEnrobéEnrobéSans fonctionnalités avancées
Hauteur une fois assemblé (cm)36,83 cm

Points saillants de l'evaluation

List of Avantages Highlights
List of Désavantages Highlights
Impossible de générer un Désavantages approprié pour le moment.

Évaluations

Sommaire de la notation

Sélectionner une ligne pour filtrer les commentaires
3 commentaires avec 5 étoiles.
7 commentaires avec 4 étoiles.
1 commentaires avec 3 étoiles.
2 commentaires avec 2 étoiles.
3 commentaires avec 1 étoile.

Note générale

3.3
7 commentateurs sur 9 (78%) recommandent ce produit

Évaluez ce produit

Sélectionnez pour évaluer l'article à 1 étoile. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 2 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 3 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 4 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 5 étoiles. Cette action ouvrira le formulaire de soumission.
Pour ajouter un avis, vous devrez fournir une adresse courriel valide à des fins de vérification.

Images et vidéos du client

Filtrer les avis

  • achat
  • petit
  • réparations
  • épais
  • facilité d'utilisation
  • application
  • la satisfaction
  • matériel
1 to 5 sur 16 commentaire
1 – 5 sur 16 commentaire

Bernzomatic Aluminum Brazing & Welding Rods

il y a 2 mois
I did not use these aluminum welding rods and returned to local store for refund,
Traduire avec Google
Utile?

not worth it

il y a 8 mois
I couldn't get it to stick no matter how hot the part gets
Traduire avec Google
Utile?
Réponse de BernzomaticProductsExpert :
il y a 8 mois
BernzomaticProductsExpert
These products are now manufactured and managed by Harris Products Group. You can contact their Customer Service team at 1-800-733-4043. Thank you! BernzomaticProducts

Works great

il y a 2 ans
Works great for what it’s designed for.
Traduire avec Google
Utile?

This product worked while another brand did not.

il y a 2 ans
I needed to braze two aluminum 2x2 inch extrusion elbow joints together for solidity. I tried another brand which did not melt until the aluminum did. I bought the Bernzomatic AL3 rods and they worked properly. I used an infrared thermometer during heating of the aluminum with a MAP gas torch to monitor the heating process. It took longer than I expected for the aluminum to get up to 730F but when it was finally there, the application of the rod went smoothly like soldering. The result is a rock solid weld so I'm good with this.
Traduire avec Google

Oui, Je recommande ce produit.

Affiché initialement sur Worthington Industries, Inc.

maybe acceptable for hobby or decorative work

il y a 2 ans
This product is not very useful for work on anything that needs to hold any kind of load or pressure. it might be good for soldering popcans together or something like that. I found that on thin aluminum lines, it would make a reasonable good looking joint, but the line would crumble right next to the edge of the solder. the line was new aluminum tubing. notes about the flux in other reviews are true: you'll have to clean material with a stainless steel brush before starting. I found it gave best results to actually tin the joint, and then wire brush in the flame to clean the surface through the molten solder, then apply a second run of solder to give a good finish. buy lots of you are going to try it, and you'll need a good mapp gas torch too like a ts8000. in the end your repair probably won't last, so probably best to just save your money and buy a new part or save up and buy a TIG :).
Traduire avec Google

Non, Je ne recommande pas ce produit.

Utile?
1 – 5 sur 16 commentaire

Questions

1 - 10 sur 13 questions

Q : Can I use this to braise two aluminum tubes together?

il y a 4 ans
Traduire avec Google
2 Réponses
  • R : Yes you can, I used these to fill a large hole in an aluminum pipe. Just make sure you don’t overheat the tube otherwise it will melt.

    il y a 4 ans
    Utile?
    Traduire avec Google

Q : How long are these rods?

il y a 6 ans
Traduire avec Google
2 Réponses
  • R : The length would be 12 inches.

    il y a 6 ans
    Utile?
    Traduire avec Google

Q : Can I use this to bond aluminum to stainless steel?

il y a un an
Traduire avec Google
1 Réponse
  • R : Hi there, thanks for reaching out! We'd recommend to exclusively use these rods when building up aluminum joints.

    il y a un an
    Utile?
    Traduire avec Google

Q : Would this work on a muffler?

il y a 6 ans
Traduire avec Google
1 Réponse
  • R : This it not a recommended use of this product. While it may work there is no guarantee of its effectiveness or that it would hold long term.

    il y a 6 ans
    Utile?
    Traduire avec Google

Q : Are these aluminum solder rods food safe for use on repairing a small hole in an aluminum pot?

il y a 6 ans
Traduire avec Google
1 Réponse
  • R : These rods are not recommended for any type of food consumption items.

    il y a 6 ans
    Utile?
    Traduire avec Google

Q : I need to repair a patio chair I believe is made of a white metal. Will this product adhere to this metal

il y a 6 ans
Traduire avec Google
1 Réponse
  • R : It will depend on the exact metal of the patio chair. As most patio furniture is made from aluminum this brazing rod can be used. However, if you have not used aluminum solder in the past it is recommend you practice on scrap metal first if possible. When soldering please ensure that the joint is clean and to not overheat it.

    il y a 6 ans
    Utile?
    Traduire avec Google

Q : I’m considering using these to fill a few 1/4” holes in an aluminum boats transom, which is 1/16” thick sheet. I read someone who said they got warping doing the same. I’m thinking a Oxy/propane tor this to get to temp quicker. Will that work? Too risky?

il y a 6 ans
Traduire avec Google
1 Réponse
  • R : Interesting project! Using the Oxy/propane torch will be too hot for this application and would cut through the metal. A TS8000 torch will have sufficient enough heat for this application but shouldn’t burn through.

    il y a 6 ans
    Utile?
    Traduire avec Google

Q : I am planning on repairing a crack on my aluminum boat. The crack spans between and around the rivet. Imagine the - is the crack and the o is the rivet. It looks like this --o---o---. Will this product work with a standard propane torch?

il y a 7 ans
Traduire avec Google
1 Réponse
  • R : Yes, you could use those solder rods but we would suggest using MAP-PRO fuel instead of Propane.

    il y a 7 ans
    Utile?
    Traduire avec Google

Q : Will this product solder pot metal to aluminum? I am looking for a product which I can use to repair or modify model cars made from unknown metals (most likely pot metal).

il y a 10 ans
Traduire avec Google
1 Réponse
  • R : Thank you for your interest in Bernzomatic products. Our AL-3 rods consist of aluminum and zinc. "Pot metal" also contains a lot of zinc, therefore the melting temperatures ( 850 degrees melting point of our AL-3) of these two are too similar. You may melt your material as well as the AL-3 rod. Standard solder ( whether a plumbing solder or more appropriate metal work solder) may be best due to the much lower melting point of 400-500 degrees of these solders. If you have any additional questions please call 1-800-359-9678 or email: Bernzomatic@WorthingtonIndustries.com

    il y a 10 ans
    Utile?
    Traduire avec Google

Q : Will this bond to brass, and if so do I require a flux

il y a 10 ans
Traduire avec Google
1 Réponse
  • R : Thank you for your interest in Bernzomatic products. Yes, this can be used for aluminum to brass connections. When used on aluminum to aluminum connections, the rods are a special formulation allowing flux not to be required. When used for other materials, Yes, flux is required. A typical plumbing flux will suffice. If you have any additional questions please call 1-800-359-9678 or email: Bernzomatic@WorthingtonIndustries.com

    il y a 10 ans
    Utile?
    Traduire avec Google
1 - 10 sur 13 questions
Haut