Obtenez votre commande dès aujourd’hui. Ramassage* ou Livraison** disponible le jour même.

En savoir plus
NOTRE MAGASIN

Crédit Offert* EN SAVOIR PLUS

Soutien État de commande
EN
Mastercraft

Agrafeuse / cloueuse à plancher Mastercraft 3-en-1

#058-8198-6
Agrafeuse / cloueuse à plancher Mastercraft 3-en-1
299,99 $

Malheureusement, cet article ne fait plus partie de l’assortiment du magasin que vous avez sélectionné et les magasins de la région.

Ces produits similaires présentés ci-dessous pourraient vous intéresser.

À l'attention des personnes résidant au Québec: pour obtenir des renseignements sur l'entretien et la réparation, cliquez ici.

Mastercraft
Mastercraft

Agrafeuse / cloueuse à plancher Mastercraft 3-en-1

299,99 $

Produit Détails

  • Agrafeuse / cloueuse à plancher Mastercraft 3-en-1 novatrice, enfonce 3 différents types de fixations

  • Consommation d'air : Débit de 0,038 pi3/min à 90 lb/po2

  • Enfonce des agrafes de parquet de 1,5 à 2 po (calibre 15) et des agrafes en T et en L de 1,5 à 2 po (calibre 16)

  • Lame d'entraînement en aluminium durci, en une pièce

  • Commande de réglage de la profondeur

  • Lame d'entraînemement spéciale durcie, en une pièce

  • Idéale pour un plancher de 3/4 po

Warranty:
  • Si cet article est défectueux, il est couvert par la garantie du fabricant. Dans le cas où aucune garantie n'est indiquée, cet article est couvert par une garantie Canadian Tire de trois ans honorée dans tout magasin Canadian Tire et il peut y avoir une garantie prolongée du fabricant.
Commande en ligne
  • Le ramassage est gratuit dans la plupart des magasins (certains magasins exigent un montant minimum de commande avant taxes).
  • Les tarifs d’expédition dépendent de la taille et du poids des articles, ainsi que de la distance entre l’adresse de livraison et le magasin.
  • La livraison le jour même coûte 9,99 $ par commande.
  • Informations sur une commande en ligne
Retours
  • La plupart des articles peuvent être retournés ou échangés dans tous les magasins Canadian Tire dans les 90 jours suivant l’achat.
  • Certains articles ne sont pas remboursables ni échangeables.
  • La politique de retour décrite ci-dessus peut ne pas s’appliquer à l’article que vous consultez présentement. Pour obtenir tous les détails et connaître les critères d’admissibilité, veuillez consulter notre Politique de retour pour connaître les exceptions.

Comparer des articles semblables

Only Show Differences
Ratings
Type d’outilCloueuse de finitionCloueuse de charpenteCloueuse de charpenteCloueuse de toiture
Calibre16 ga15 ga11 ga11 ga
Longueur de fixation maximale (po)2,52 po3,54 po3,25 po1,77 po

Offres hebdo

Évaluations

Sommaire de la notation

Sélectionner une ligne pour filtrer les commentaires
8 commentaires avec 5 étoiles.
17 commentaires avec 4 étoiles.
4 commentaires avec 3 étoiles.
1 commentaires avec 2 étoiles.
20 commentaires avec 1 étoile.

Note générale

2.8
29 commentateurs sur 50 (58%) recommandent ce produit

Évaluez ce produit

Sélectionnez pour évaluer l'article à 1 étoile. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 2 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 3 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 4 étoiles. Cette action ouvrira le formulaire de soumission.
Sélectionnez pour évaluer l'article à 5 étoiles. Cette action ouvrira le formulaire de soumission.
Pour ajouter un avis, vous devrez fournir une adresse courriel valide à des fins de vérification.

Images et vidéos du client

Filtrer les avis

  • achat
  • prix
  • bois
  • retours
  • valeur
  • installation
  • petit
  • ajustabilité
1 to 5 sur 50 commentaire
1 – 5 sur 50 commentaire

tres facile autiliser

il y a 5 ans
j'ai fait mon plancher de 800 pi carres et fonctionne a merveille

Oui, Je recommande ce produit.

Utile?

058-8198-6 Nailer leaks air

il y a 8 ans
This nailer is a piece of junk. It leaks air out of the handle. Looking at the parts list, there is nothing in the handle. I have taken it into my Canadian Tire store, they don't care about the nailer not working, it has never worked. All they want is the receipt, which of course I do not have. All I want is for someone to look at the nailer & tell me why it is not working. If someone from Canadian Tire would like to look at the floor nailer that I bought, you can contact me at my email address.
Traduire avec Google

Non, Je ne recommande pas ce produit.

Utile?

good for sale price

il y a 11 ans
this nailer works good but it is not a heavy duty contractor tool.If you want to put a few floors down in your home ,this nailer will do.If you plan on making a living with it,this is not the tool for you.
Traduire avec Google

Oui, Je recommande ce produit.

Utile?

eactly what I need

il y a 11 ans
I bought this for my future project, did not used it yet. the 4 stars only for the price.
Traduire avec Google

Oui, Je recommande ce produit.

Utile?

Cheap, worked well, nightmare service

il y a 11 ans
I installed my first floor by using a rented nailer in leisure time. The rent was expensive. I saw this product on sale which is very cheap comparing to other brands and the rent cost. So knowing the pros and cons after read the reviews I bought it for my second floor . Worked very well but after installed about 800 sq foot, the driver started causing problem. No matter how often I clean the drive channel and use lubricant, the driver just does not spring back fully often and often. So I had to call service number and brought it to their service depot Swish in Oakville. After two weeks, I got the call and the product was ready for pickup. I hooked it to compressor to test but the air leaked between the body and the cap (This is new problem). I could not even test the driver (But they said they tested before call me but I cannot figure it out how test it without enough air pressure.). I brought it back to the service depot second day. After one month long waiting, no call. I had to call them. To my surprise I had to pay for the service because them did not find anything wrong! They said that the air leaking could be caused by the air compressor (I just don't understand how this could happy but they insist and ask me bring in the compressor if the the air still leak but they will charge for the inspection of my compressor!) OMG, I must be crazy to bring a working nailer to the service and let the unfinished floor be a mess for one and half month! Maybe they realized that I am not so low in IQ and waived the half hour labor charge. I would recommend this product to others if they want a very cheap, flexible, and disposable nailer for small projects.
Traduire avec Google

Oui, Je recommande ce produit.

Utile?
1 – 5 sur 50 commentaire

Questions

1 - 10 sur 26 questions

Q : What brands of 1.5" "L" cleats are compatible and where can I get them? I want to install 5/8" bamboo hardwood flooring. The recommendation is 1 1/2" "L" 16 gauge flooring cleats. I could not find them at Canadian Tire. Will any brand of 1 1/2" L 16 gauge cleat work in the Mastercraft 3 in 1 flooring nailer?

il y a 14 ans
Traduire avec Google
4 Réponses
  • R : I used bosh with no problems

    il y a 14 ans
    Utile?
    Traduire avec Google

Q : Will it work on 3/4 in hardwood flooring? What size nails

il y a 12 ans
Traduire avec Google
2 Réponses
  • R : Yes, it works best on 3/4 flooring.

    il y a 12 ans
    Utile?
    Traduire avec Google

Q : You sell the same nailer with two different packages: the older specifies 15.5 gauge staples; the newer: 15 gauge staples. Which is correct?

il y a 12 ans
Traduire avec Google
2 Réponses
  • R : 15.5 fit... however this nailer is junk stay away

    il y a 11 ans
    Utile?
    Traduire avec Google

Q : Does this include hammer/ mallet?

il y a 12 ans
Traduire avec Google
2 Réponses
  • R : came with one when I purchased mine

    Anonymeil y a 12 ans
    Utile?
    Traduire avec Google

Q : The nailer is firing too deep. How to adjust? Fires 2" cleats way too deep I tried turning the whack cap CCW as instructed, no change in depth. Anything else I can try? I run at 90 psi which Instructions say is minimum.

il y a 13 ans
Traduire avec Google
2 Réponses
  • R : SImple reduce the PSI, use a scrap piece of wood, try at 80psi first and go from there.

    il y a 13 ans
    Utile?
    Traduire avec Google

Q : Where can I get parts for this nailer? I have a leak coming from the handle. I've opened it up and it is leaking through what I think is some sort of regulator...There is a spring attached to this part, if that helps.

il y a 13 ans
Traduire avec Google
2 Réponses
  • R : I fixed the leak from my handle simply using the included Allen key to torgue up the screws that hold the handle to the body.

    il y a 13 ans
    Utile?
    Traduire avec Google

Q : What is the magazine capacity, operating pressure and max PSI?

il y a 13 ans
Traduire avec Google
2 Réponses
  • R : not sure of the mag capacity, but it takes an entire row out of a standard box of floor nails! Operating PSI is 90, however i have run it between 90psi and 100psi, Reason for this is 90 psi was great for regular wood, but the bamboo i'm working with now is 3 times harder than red oak, so i'm running at 99-100psi. You should really have a compressor that allows you to adjust the psi setting.

    il y a 13 ans
    Utile?
    Traduire avec Google

Q : Will it fire properly with 2 HP peak (1.1 running) and 3.7 scfm@90 compressor

il y a 13 ans
Traduire avec Google
2 Réponses
  • R : cfm is not important but you need about 100psi at the tool

    il y a 13 ans
    Utile?
    Traduire avec Google

Q : Will it fire properly with 4 CFM? After checking the CFM needed, nervous about working with my compressor 26 gal. 1.5HP oil-less - 5 cfm at 40lbs & 4 cfm at 90lbs. I checked other brands - haven't seen any that will deliver this high CFM.

il y a 14 ans
Traduire avec Google
2 Réponses
  • R : I assure you that you will work so slowly with this tool that cfm will never be an issue. You need about 100psi to drive successfully.

    il y a 13 ans
    Utile?
    Traduire avec Google

Q : Can 18 guage cleats be used with this nailer?

il y a 14 ans
Traduire avec Google
2 Réponses
  • R : No, 16ga only

    il y a 13 ans
    Utile?
    Traduire avec Google
1 - 10 sur 26 questions
Haut