CANADA'S STORE Made for Life in Canada

Credit Offered* Learn More

Save on summer must-haves
including bikes, BBQs, pools, trampolines, outdoor furniture, and more.

WINDOW AIR CONDITIONER

It is recommended to store the window air conditioner indoors during the winter.

Check the filter every 2 weeks to see whether it needs cleaning.

NOTE: Do not operate the air conditioner without the filter in place.

1. Turn off the air conditioner.

2. Open the front panel. Grasp the centre of the filter and pull up and out.

3. Use a vacuum cleaner to clean the air filter. If the air filter is very dirty, wash it in warm water with a mild detergent. Do not wash the air filter in the dishwasher or use any chemical cleaners. Air dry the filter completely before replacing to ensure maximum efficiency.

4. Replace the air filter back into the air conditioner, and close the front panel.

Please refer to the User Manual for instructions.

1. Run the air conditioner set to Fan Only for approximately 12 hours to dry the air conditioner.

2. Unplug the air conditioner.

3. Remove all accessories and store with the air conditioner in a clean, dry area. See "Installation Instructions“ in User Manual.

4. Remove the filter and clean. See "Cleaning the Air Filter".

5. Clean the air conditioner. See "Cleaning the Front Panel".

6. Reinstall the filter.

7. Remove the batteries and store the remote control with the air conditioner upright in a clean, dry area. 

The 10,000 and 12,000 BTU units have the same dimensions. The unit’s exterior dimensions are L x W x D 18 7/8 x 21 7/8 x 14 9/16"

(48 x 55.5 x 37 cm). The window dimensions should be at least larger than L x W: 18 7/8 x 21 7/8" (48 x 55.5 cm).

Yes, it's normal for water to be dripping outside.

The filter can be found in the front panel.

The highest temperature that can be set is 30°C (86°F), and the lowest temperature that can be set is 16°C (60°F).

The serial number can be found on a label on the window AC unit. The label is located on the top of the AC unit.

In the event of a power outage, the device will automatically restart to its original state once power is restored.

1. Fan: Only the fan runs without cooling. The fan speed can be adjusted from low, medium and high.

2. Dry: Dries the room to reduce the humidity. The AC automatically selects the temperature and low fan speed.

3. Cool: Cools to reduce the room temperature. The fan speed can be adjusted from low, medium or high.

4. Eco: Eco cools the room while saving energy. This mode slowly runs your AC compressor, which reduces the pressure in the condenser and allows the motor to consume less energy to run the unit.

1.  Initial Setup

When the device is plugged in, the WiFi LED will flash slowly indicating that the unit is in pairing mode. In order to pair the device, please enable and give permission for Locations Services and Bluetooth on your mobile device. In the NOMA iQ app, select the “+” symbol in the top right hand corner. Select the device and follow the instructions within the app.

2.  Pre-Connected Network

If any pre-connected WiFi network is found, the device will connect automatically and the WiFi LED will remain lit.

3.  No Pre-Connected Network

If no pre-connected WiFi network is found, make sure the device is in pairing mode (see step 5). Once connected, the WiFi LED will remain lit.

4.  No Network Found

If no WiFi network is found after 5 minutes during the pairing process, the WiFi function will automatically turn off and the WiFi LED will turn off. The unit can still be used with the control panel or remote control.

5.  Reset WiFi Connection/Pairing Mode

To reset your WiFi connection or to set the device to pairing mode, press and hold the "CONNECT" icon on the control panel until the WiFi LED starts flashing indicating that the device is in pairing mode. In order to pair the device, please enable and give permission for Locations Services and Bluetooth on your mobile device. In the NOMA iQ app, select the “+” symbol in the top right hand corner. Select the device and follow the instructions within the app.

6.  No Cloud Connection

If the Cloud is down or WiFi signal drops, the device cannot connect to the cloud; the WiFi LED will turn off.

7.  Power Cycle or Outage

Once a connection has already been established, in the event of a power outage, the unit will restart once power is restored. If the unit is unplugged, plug the device back in and the device will connect to the pre-connected network. If the device has not been paired, upon power up it will go to Initial Setup (see Step 1).